Difference between revisions of "Locator Tutorial: Setting up Locator to work with SIASUN robots"

From 3D scanning Knowledge base - Photoneo wiki
Jump to: navigation, search
(Created page with "'''It is highly recommended that users read [http://wiki.photoneo.com/index.php/Locator_Tutorial:_Introduction Locator Tutorial: Introduction] prior to installation of specifi...")
 
Line 3: Line 3:
 
== 1. Prerequisities ==
 
== 1. Prerequisities ==
  
Locator SIASUN Interface is compatble with SIASUN UI: 2.0.5, Robot: 1.0.5  
+
Locator SIASUN Interface is compatible with following system version: UI: 2.0.5, Robot: 1.0.5 or higher.
  
 
Check your robot system version before proceeding further, on Main Menu Click About Tab:
 
Check your robot system version before proceeding further, on Main Menu Click About Tab:
 +
  
 
[[File: SIASUN Locator Tutorial About.png]]
 
[[File: SIASUN Locator Tutorial About.png]]
 +
 +
 +
If your pendant is still in Chinese, select Settings tab and Switch language to English at the bottom of the page:
 +
 +
 +
[[File:SIASUN Locator Tutorial Language.png]]
 +
 +
== 2. SIASUN Controller setup ==
 +
 +
The following tutorial gives a step by step guide of how to configure your SIASUN robot controller and install all the necessary files you will need to get the robot interface for Locator up and running.
 +
 +
This tutorial was originally written using the latest collaborative SCR5 with system version UI: 2.0.5, Robot: 1.0.5
 +
 +
=== 2.1 Network Configuration ===
 +
 +
The Locator SIASUN Module utilizes TCP/IP communication for transferring data between SIASUN Robot Controller and Vision Controller.
 +
 +
As a first step in commissioning, ensure that the IP address of the SIASUN controller meets your network configuration requirements
 +
 +
Browse to '''Settings''' -> '''IP Address''', select '''Static''' option and configure network settings of robot controller:
 +
 +
 +
[[File: SIASUN Locator Tutorial IP Config Step 1.png]]
 +
 +
 +
Confirm new network configuration by clicking on '''YES''' button:
 +
 +
 +
[[File: SIASUN Locator Tutorial IP Config Step 2.png]]
 +
 +
 +
The new network configuration is applied immediately, reboot is not necessary.

Revision as of 20:44, 26 November 2018

It is highly recommended that users read Locator Tutorial: Introduction prior to installation of specific robot interface

1. Prerequisities

Locator SIASUN Interface is compatible with following system version: UI: 2.0.5, Robot: 1.0.5 or higher.

Check your robot system version before proceeding further, on Main Menu Click About Tab:


SIASUN Locator Tutorial About.png


If your pendant is still in Chinese, select Settings tab and Switch language to English at the bottom of the page:


SIASUN Locator Tutorial Language.png

2. SIASUN Controller setup

The following tutorial gives a step by step guide of how to configure your SIASUN robot controller and install all the necessary files you will need to get the robot interface for Locator up and running.

This tutorial was originally written using the latest collaborative SCR5 with system version UI: 2.0.5, Robot: 1.0.5

2.1 Network Configuration

The Locator SIASUN Module utilizes TCP/IP communication for transferring data between SIASUN Robot Controller and Vision Controller.

As a first step in commissioning, ensure that the IP address of the SIASUN controller meets your network configuration requirements

Browse to Settings -> IP Address, select Static option and configure network settings of robot controller:


SIASUN Locator Tutorial IP Config Step 1.png


Confirm new network configuration by clicking on YES button:


SIASUN Locator Tutorial IP Config Step 2.png


The new network configuration is applied immediately, reboot is not necessary.